Armacell Products: Armacell Flare Fittings

The BEST things in life are FREE!
	Quotation Service
	Valuation Service
	Advice

What can I help you with?

Do you need a brochure?
Is it a quote you're after?
Can I help you with a technical question?
Do you need a sample?

Armacell Materials: Armacell Flare Fittings

Below you will find information on specific products within our range. To ensure that you purchase the correct products to suit your requirements we recommend that, you contact one of our qualified customer focused advisors, who will be only too pleased to help. Please call 08451 306 269 or email us for a quote or advice.

Armacell Flare Fittings

Armacell SAE flare fittings meet the highest safety standards and replace soldering in a fast, safe and economic way. No additional sealing is required, only metal-to-metal sealing by the rim on the flare of the compression ferrule. The nut made of brass alloy fits perfectly on the tube armature, and the most important part -the compression ferrule- takes over the sealing much better than the traditional hand-made flared end to the copper tube very effectively. No copper gasket is needed and none of the pieces have to be replaced after maintenance and repair.

Secure and fast solution for split installations.
Avoids problems normally associated with traditional soldering.
No specialist flare tools required.
No hot working permit required.
Gas tight and highly resistant to mechanical damage.
Complies with new CEN regarding refrigeration gases.


	Description / Values
Standards	Corresponds to the new standards and regulations of the CEN for refrigeration installations (EN 378/1 + EN 378/2 ).
Technical Features	No copper sealing necessary Compression ferrule Tight up to 10-7 mbar l /s respectively <= 0,5 gr/a Helium for all refrigerants ( CFC/HFC/HCFC) Tight connection: no leaky connections, higher safety standard, meets test procedure DQJ/KP/926/99 developed by the refrigeration commission. Meets the new standards EN378:2000 for refrigeration systems and heat pumps - Safety and environmental requirements - Part 2 (design,construction, testing, marking and documentation).
Supervision & Certificates	Tested by internal test procedures according to DIN 3859 and by CETIM: Reverse-bending strength test: no leakage after 10 Mio. cycles at 50 Hz under nominal pressure Helium-leakage detector (gas tightness) : < 0,5 g/year (10-6 mbar/l/s) Burst-pressure test (4 times nominal pressure): no leakage Temperature cycle test (5 cycles at -40º C to +120 ºC at 10 bar He): no leakage CETIM, Internal and field test results

ARMACELL SAE Flare Fittings
Description	Reference	Copper tube OD inch	Copper tube thickness mm	Pressure nominal (bar)	Sets per carton
SAE-Flare Fitting 1/4^*	SF-FZ50-006	1/4	0.8	100	50
SAE-Flare Fitting 3/8^*	SF-FZ50-010	3/8	0.8	64	50
SAE-Flare Fitting 1/2^*	SF-FZ50-012	1/2	0.8	45	50
SAE-Flare Fitting 5/8^*	SF-FZ50-016	5/8	1	45	50
SAE-Flare Fitting 3/4^*	SF-FZ-019	3/4	1	45	50
* The SAE Flare Fittings are supplied in small bags of 10 sets. Each carton contains 5 bags. One set contains a stiffener sleeve, a compression ferrule and a union nut.

ARMACELL SAE Calibration Tool
Description	Reference	Copper tube OD inch	Copper tube thickness m	Sets per carton
Calibration tool 1/4^*	SF-CTZ-006	1/4	0.8	10
Calibration tool 3/8^*	SF-CTZ-010	3/8	0.8	10
Calibration tool 1/2^*	SF-CTZ-012	1/2	0.8	10
Calibration tool 5/8^*	SF-CTZ-016	5/8	1	10
Calibration tool 3/4^*	SF-CTZ-019	3/4	1	5
* The calibration tools are supplied in small bags of 1 set. Each carton contains 10 bags. * All calibration tools are as well available as single sets.